ethernet status says i have 1gbps. only getting 1.8

ETHERNET STATUS SAYS I HAVE 1GBPS. ONLY GETTING 1.8 DRIVER
ETHERNET STATUS SAYS I HAVE 1GBPS. ONLY GETTING 1.8 FULL

Thank you for any assistance, in advance. That Switch is connected to a x-box as well, which gets over 700 Mbps when testing on Xbox network settings, so I'm sure it's not the switch or the router at this point, nor the cabling.Īny help would be appreciated. When I do right-click on the network adapter and I selected 'Status' it showed me the speed 100Mbps, instead of 1Gbps. I've changed ports on my router, which goes to a Pakedge SE-8 Gigabit unmanaged Switch I'm connected to a HP Thunderbolt Dock G2, as there are no ethernet ports on the Elitebook.Ī few more troubleshooting points I've done: I've tried the cord that I'm using (Cat6) on a separate computer that has an ethernet port, and the settings on Ethernet Status show 1 Gbps instead of the 100 Mbps that I am getting, so I do not think it is the cord. 2 shows the service class utilization factors of the considered. So I have changed back to 'Auto Negotiation' within these properties. GigabitEthernet 1 Gbits/s H H 1 0.18 0.16 0.1s delay bound, Ethernet 0.14 0.12 0.1.

ETHERNET STATUS SAYS I HAVE 1GBPS. ONLY GETTING 1.8 FULL

I've tried to change the 'Speed & Duplex' in the 'Realtek USB GbE Family Controller #4' properties, to 1 Gbps Full Duplex, but that doesn't seem to do anything. My wireless speeds are upwards of 650 Mbps, however, when I plug my ethernet cord into the dock, which is then connected via USB-C to the Eliltebook the Speed in my 'Etherent Status' window is stuck at 100.0 Mbps. Consider the TP-Link Archer AX73, our budget pick for the best long-range routers, if you have a larger home.Recently I've updated to CenturyLink gigabit service for internet. Overall, the TP-Link Archer AX10 should be your budget pick for apartments and small homes. So if you’ve got a 1.2 Gbps internet plan, you won’t have access to all of that speed on any one Ethernet connection.īut since you’re probably spreading your bandwidth over multiple devices, we don’t think this will cause problems for most folks.

One heads up, though: While the TP-Link Archer AX10 can wirelessly support up to 1.2 Gbps on its 5 GHz router, its fastest LAN port will give you a wired connection of up to only 1 Gbps. If you want gigabit speeds and don’t need long-range or gaming perks, snag this speedy little pal. I tried changing 'Speed & Duplex' to 1.0 Gbps Full Duplex, but that disconnects the adapter and the network connection does not work. This way I expect the 'Speed' in Ethernet Status -> General to be shown as 1 Gbps, but it stays at 100 Mbps.

ETHERNET STATUS SAYS I HAVE 1GBPS. ONLY GETTING 1.8 DRIVER

Application Control Throughput (HTTP 64K)2. The driver Properties -> Advanced -> Speed & Duplex is set to 'Auto Negotiation'. The cable that connects between two switches was getting 1Gbps. FortiGate Network Security Platform - Top Selling Models Matrix. I have another long Cat5e that connects between switch 1 to the other end of the basement where switch 2 is, the length is only 74 feet. Then, using another cable from switch 1 to my laptop. This will open the Network Connections window. Once I got 1Gbps, i connect it the cable to switch 1. Sure, the GT-AX11000 may be seven times faster (under perfect lab conditions), but the TP-Link Archer AX10 is six times cheaper (under everyday life conditions). Under the Start Menu, search for View Network Connections, and as the result appears, press Enter or click on it. If the cost of ASUS ROG Rapture GT-AX11000 gave you pause, consider the affordable alternative: the TP-Link Archer AX10. Not everyone who pays for gigabit speeds wants to drop a handful of 100 dollar bills on a router.

Ethernet status says i have 1gbps. only getting 1.8